AES 7170 Specifications Page 1

40-7170 Revision 2B July 6, 2012 1 AES 7170 IP-Link Transceiver (Remote & Local) Installation and Operation Manual

40-7170 Revision 2B July 6, 2012 10Solder Method: Soft solder contact to cable center conductor. Do not get any solder on outside surface of contac

40-7170 Revision 2B July 6, 2012 116.0 Wiring (Electrical Inputs and Outputs): Listed below are the termination points and connectors in the IP-Li

40-7170 Revision 2B July 6, 2012 12NOTE: DO NOT POWER UP THE IP-LINK TRANSCEIVER UNTIL ITS MULTINET RECEIVER IS ON-LINE AND READY FOR THIS UNIT TO

40-7170 Revision 2B July 6, 2012 13 Figure K. RF Control Board, Input terminal Block Figure I. Power Connector B. Terminal Block Connection Det

40-7170 Revision 2B July 6, 2012 147.0 Indicators: There are several LED indicators and one speaker in the IP-Link transceiver. Below are descript

40-7170 Revision 2B July 6, 2012 15

40-7170 Revision 2B July 6, 2012 16 8.0 Programming and Setup of the 7170 IP-Link Transceiver: NOTICE TO USERS, INSTALLERS, AUTHORITIES HAVING

40-7170 Revision 2B July 6, 2012 17A. Communicating with the 7170 IP-Link Transceiver: Listed below are instructions for configuring several termin

40-7170 Revision 2B July 6, 2012 18 Figure M – HyperTerminal - Connect To 3. Do Not enter any Details for the Country/region, Area code or Phone n

40-7170 Revision 2B July 6, 2012 19 Figure N – HyperTerminal - COM Properties 6. You are now ready to use HyperTerminal. Figure O – HyperTermin

40-7170 Revision 2B July 6, 2012 2Table of Contents 1.0 Product Description: AES 7170 IP-Link System: ...

40-7170 Revision 2B July 6, 2012 204. Press <Alt> T to change or check terminal emulation mode. Next select (highlight) “ANSI”. Press <

40-7170 Revision 2B July 6, 2012 21If the Port is switched to Console (Modem LED off) then the S<Enter> option should be available.

40-7170 Revision 2B July 6, 2012 22Bios Version 3.3c for uFlashTCP with NE2000 EthernetDOC Socket Services - Version 0.2 (C) Copyright 1992-1996,

40-7170 Revision 2B July 6, 2012 23my_ip=192.168.0.11 OR my_ip=dhcp gateway=192.168.0.1. netmask=255.255.255.0 C. Configuring the 7170 IP-

40-7170 Revision 2B July 6, 2012 24C.3. Set Up Menu: There are several methods to access the Setup Menu using a terminal program attached to the Co

40-7170 Revision 2B July 6, 2012 25U: TCP/IP Socket Timeout is the time that the unit waits for an ACK for a sent TCP/IP packet. Default is 12.

40-7170 Revision 2B July 6, 2012 26C.4. Test the network connection: • From a command prompt, reached by pressing X after a reset you can confirm

40-7170 Revision 2B July 6, 2012 279.0 Testing the 7170 IP-Link Transceiver: There are several functions of the IP-Link Transceiver that can be tes

40-7170 Revision 2B July 6, 2012 28To test your IP-Link’s RF signal you need to connect a power meter or SWR meter in the coax line to read power.

40-7170 Revision 2B July 6, 2012 2910.0 Warranty / Service Procedures: AES CORPORATION LIMITED PRODUCT WARRANTY AND TECHNOLOGY LICENSE LIMITED PRO

40-7170 Revision 2B July 6, 2012 3

40-7170 Revision 2B July 6, 2012 41.0 Product Description: AES 7170 IP-Link System: MultiNet is an AES IntelliNet system that uses the Internet to

40-7170 Revision 2B July 6, 2012 5Following is a list and diagram of key components. □ Figure B. Typical 7170 IP-Link Transceiver Installation A

40-7170 Revision 2B July 6, 2012 6B. ASM Antenna Supervision Module (7170SWR) This module is placed in series with the RF connection between the tr

40-7170 Revision 2B July 6, 2012 72.0 Safety Considerations: The following items are safety related precautions that you should take into consider

40-7170 Revision 2B July 6, 2012 85.0 Installation: The IP-Link Transceiver installation site is a critical element of the AES IntelliNet network.

40-7170 Revision 2B July 6, 2012 9is not necessary. Ideally, select an antenna height and the 7170 IP-Link Transceiver location that will use less